background image

INSTALLATION

Continued 

INSTALLING HEATER BASE 
ASSEMBLY

 WARNING: You must secure 

this heater to fireplace floor. If 

not, heater will move when you 

adjust controls. Moving heater 

may  cause  a  gas  leak  or  log 

misplacement.

  WARNING:  If  installing  in  a 

sunken  fireplace,  special  care 

is  needed.  You  must  raise  the 

fireplace floor to allow access to 

heater control panel. This will in

-

sure adequate air flow and guard 

against sooting and controls be

-

ing damaged. Raise fireplace floor 

with  noncombustible  material. 

Make sure material is secure.

  CAUTION:  Do  not  pick  up 

heater base assembly by burners. 

This could damage heater. Only 

handle base assembly by grates.

IMPORTANT:

 Make sure the heater burners are 

level. If heater is not level, heater will not work 

properly. 

Installation Items Needed

•  hardware package (provided with heater)

•  approved flexible gas hose and fittings (not 

provided) (if allowed by local codes) 

• 

sealant (resistant to propane/LP gas, not 

provided)

•  electric drill with 3/16" drill bit (metal or ma

-

sonry as applicable)

•  flathead screwdriver

•  pipe wrench

1.  Apply pipe joint sealant lightly to male threads 

of gas fitting (not provided). Connect approved 

flexible gas hose to gas control fitting in heater 

(see Figure 11). 

IMPORTANT:

 Hold gas fitting 

with wrench when connecting flexible gas hose.

2.  Locate two masonry screws in hardware package. 

3.  Place heater base in fireplace.

4.  Place logs in their proper position on heater 

base (see 

Installing Logs

, page 16).

5.  Center heater base and logs front-to-back 

and side-to-side in fireplace.

6.  Carefully remove logs without moving heater 

base.

7.  Mark screw locations through one hole on 

each side of the base (see Figure 12). If install

-

ing in a brick-bottom fireplace, mark screw 

locations in mortar joint of bricks.

8.  Drill holes at marked locations using 3/16" 

drill bit. 

9.  Attach base assembly to fireplace floor using 

two masonry screws (in hardware package).

Figure 11 - Attaching Flexible Gas Hose 

to Heater

Flexible Gas Hose (if 
allowed by local codes)

Fitting

Figure 12 - Attaching Heater to Fireplace 

Floor

Masonry Screw

Screw Holes 
in Base

INSTALLING BATTERIES FOR 
REMOTE RECEIVER AND HAND 

HELD REMOTE CONTROL

Four AA batteries and three AAA batteries are 

required to operate this heater with the wireless 

hand-held remote control set. Four AA batteries 

must be installed in the receiver and three AAA 

batteries in the hand-held remote control unit. 

Note:

 Only use alkaline batteries.

Содержание LDL3924NR
































Отзывы: