manualshive.com logo in svg
background image

 

 

Doc No. 700025  Page   of 32 

INDEX

 

Section 

 

 

Introduction and Document Index 

 Installation 

Requirements -------------------------------------------------- 1 

 Assembly 

Instructions 

------------------------------------------------------- 

Commissioning Instructions ----------------------------------------------- 3 

Servicing Instructions -------------------------------------------------------- 4 

Spare Parts -------------------------------------------------------------------- 5 

Fault Finding Guide ---------------------------------------------------------- 6 

Replacing Parts --------------------------------------------------------------- 7 

User and Operating Instructions ------------------------------------------ 8 

A

A

MBI

MBI

R

R

AD

AD

 

 

V

V

ISION

ISION

®

 

 

VT R

VT R

ANGE

ANGE

 

 

R

R

ADIANT

ADIANT

 

 

T

T

UBE

UBE

 

 

H

H

EATERS

EATERS

 

 

I

I

NSTALLATION

NSTALLATION

 

 

AND

AND

 

 

O

O

PERATING

PERATING

 

 

M

M

ANUAL

ANUAL

 

 

Part No. 700025 

Nortek Global HVAC (UK) Limited,  Fens Pool Avenue,  Brierley Hill,  West Midlands,  DY5 1QA 

WARNINGS 

 

Nortek Global HVAC (UK) Ltd equipment must be installed and maintained in accordance with 
the relevant provisions of the Gas Safety (Installations and Use) Regulations 1998 for gas fired 
products. Due account should also be taken of any obligations arising from the Health and Safe-
ty at Works Act 1974 or relevant codes of practice. In addition the installation must be carried 
out in accordance with the current IEE wiring regulations (BS 7671), BS 6896 (Industrial & Com-
mercial) and any other relevant British Standards and Codes of Practice by a qualified installer. 
All external wiring MUST comply with the current IEE wiring regulations.  

Содержание VISION VT Series

































Отзывы: