background image

www.desatech.com

122526-01B

23

OPERATION

FOR YOUR SAFETY 

READ BEFORE LIGHTING

 WARNING: If you do not fol-

low  these  instructions  exactly, 

a  fire  or  explosion  may  result 

causing property damage, per-

sonal injury or loss of life.

A.  This appliance has a pilot which must 

be lighted by hand. When lighting the pi-
lot, follow these instructions exactly.

B.  BEFORE  LIGHTING  smell  all  around 

the appliance area for gas. Be sure to 
smell next to the floor because some 
gas is heavier than air and will settle 
on the floor.

 

WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do 

not use any phone in your building.

• Immediately  call  your  gas  supplier 

from a neighbor’s phone. Follow the 
gas supplier’s instructions.

• If you cannot reach your gas supplier, 

call the fire department.

C.  Use only your hand to push in or turn 

the gas control knob. Never use tools. 
If the knob will not push in or turn by 
hand, don’t try to repair it, call a quali-
fied service technician or gas supplier. 
Force or attempted repair may result in 
a fire or explosion.

D.  Do  not  use  this  appliance  if  any  part 

has been under water. Immediately call 
a qualified service technician to inspect 
the appliance and to replace any part of 
the control system and any gas control 
which has been under water.

LIGHTING 

INSTRUCTIONS

 WARNING:

•  If  fireplace  has  glass  doors, 

never operate this heater with 

glass doors closed. If you op-

erate heater with doors closed, 

heat  buildup  inside  fireplace 

will cause glass to burst. Make 

sure there are no obstructions 

across openings of fireplace.

•  You must operate this heater 

with a fireplace screen in place. 

Make sure fireplace screen is 

closed before running heater. 

NOTICE: During initial operation of 

new heater, burning logs will give 

off a paper-burning smell. Orange 

flame will also be present. Open 

damper or window to vent smell. 

This will only last a few hours. 

Note: Home owners generally prefer to operate 
their  heater  with  the  chimney  damper  closed. 
This will put all the heat into the room. However, 

there may be times you will desire the full flames 
of the HI heat setting but will find the heat output 

excessive. You can open the chimney damper (if 
you have one) fully or partially to release some 
of the heat.

  WARNING:  Damper  handle 

will  be  hot  if  heater  has  been 

running.

1.  STOP! Read the safety information, col

-

umn 1.

2.  Make sure equipment shutoff valve is fully 

open.

3.  Set switch to OFF position. 
4.  Press in and turn control knob clockwise 

 to the OFF position (see Figure 39, 

page 24).

5.  Wait five (5) minutes to clear out any gas. 

Then  smell  for  gas,  including  near  the 
floor. If you smell gas, STOP! Follow “B” 
in the safety information, column 1. If you 
don’t smell gas, go to the next step.

Содержание EC18NR









































Отзывы: