Deprag 346-138U Скачать руководство пользователя | Manualshive

Страница: 17 / 40

background image

17

11. Unscrew threaded fitting 396582 from motor housing 396578 by means

of pin wrench 462325.

12. Remove both wedges 326946 from motor housing 396578 by means of

assembly pin 460744.

13. Slide the complete motor- and gearing package out of the motor housing

396578 in direction of the air inlet.

a.  Clamp rotor cylinder into fixing device.
b.  Pull off shaft-side bearing cover from rotor.
c.  Remove rotor cylinder.

NOTE

Exchange only complete sets of vanes.

d. Remove vanes and check them thoroughly. Vanes that are too narrow

or damaged have to be replaced

in sets

.

e. Pull off air connecting-side bearing cover from rotor.
f. Press the two ball bearings from the bearing covers.

Minimum vanes width should be 8 mm.

Assembly:

Use the DEPRAG Grease 807293 (100-g tube) to grease the
ball bearing, needle bearing and gearing parts prior to
reassembly.

For assembly proceed logically in reverse order with reference to disassem-
bly!

Special Repair Tools (Optional Equipment)

N

AME

P

ART

N

O

.

Arbor (to disassemble bearing cover with groove ball bearing)

462330

Press-in device (for bearing cover + rotor)

462203

Assembly pin (for wedge 326946)

460744

Arbor (to assemble circlip 800248 onto spindle)

461292

Chucking jaws (for exterior motor housing 3979471)

462506

Pin wrench (for threaded fitting 396582)

462325

Pin wrench (for threaded fitting 402372)

462581

Key (for threaded fitting 384731)

462125

Assembly arbor
(for assembly of bearing needle 802332 in clutch shaft 331562)

460405

Fixing device (for rotor cylinder)

460475/1

«
...
15
16
17
18
19
...
»

Содержание 346-138U









































Отзывы:

Нет отзывов

Похожие инструкции для 346-138U

Бренд: Caen Страницы: 17

Бренд: Campbell Страницы: 2

Бренд: OBO Bettermann Страницы: 2

Color Block PSU-05B

Бренд: Chroma Страницы: 2

PSI 9000 Series

Бренд: Electro-Automatik Страницы: 64

Бренд: Conrad Страницы: 3

Belleta iPB Series

Бренд: TDK Страницы: 2

Бренд: PTN Страницы: 24

Бренд: TekPower Страницы: 4

Wi-Fi Anywhere PTE2700

Бренд: JVA Страницы: 8

Бренд: Milwaukee Страницы: 37

Бренд: Aaeon Страницы: 11

Truck PAC ES-6000

Бренд: Clore Automotive Страницы: 48

Бренд: Elvox Страницы: 12

Бренд: Xtreme Страницы: 8

Бренд: Nervus Страницы: 20

Бренд: CyberPower Страницы: 2

Бренд: CyberPower Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды