background image

8

ROTARY HAMMER

EN

 

 choosing the feed force when drilling or chiseling, focus on reducing engine speed under load: decrease the rotation 
more than 20% compared to idle leads to a significant deterioration in engine cooling and indicates overload;

 

 do not overheat external Electrical Rotary Hammer parts during long work. If there is an excessive heat, stop 
working, let the Electrical Rotary Hammer work without load for 1-2 minutes for engine cooling, turn off the 
engine and take a break until the gear housing becomes cool;

 

 do not allow the Electrical Rotary Hammer work when there is extraneous or uncharacteristic noise in the engine 
or gear. When there are noises turn off the Electrical Rotary Hammer and contact an authorized service;

 

turn off the Electrical Rotary Hammer with the switch before disconnecting from the power supply.

ATTENTION!

If during the usage the Electrical Rotary Hammer unexpectedly shuts down work it is necessary:
1.   To turn the power key to "off" immediately and disconnect the power cable from the outlet.
2.   To inspect the drill and electrical cable for damage carefully. If damage is found, contact the 

service center. 

3.   To check for mains voltage.
4.   To carry out trial switch on by turning the switch key to the “on” position for 1-2 sec. If in the 

presence of power in the mains the Electrical Rotary Hammer does not turn on, you need to 
contact the service center.

At the end of the work:

 

disconnect the Electrical Rotary Hammer from the mains, making sure the switch is in the off position;

 

clean the Electrical Rotary Hammer and accessories from dirt;

 

with a long break in work lubricate the box with a layer of conservation grease;

 

periodically clean the ventilation holes with a soft brush and vacuum cleaner.

NOISE AND VIBRATION

Noise and vibration characteristics are given in the "Specifications table".
However, if the Electrical Rotary Hammer is used for other work with the use of working toolings, not provided 
by the manufacturer, or maintenance does not meet the requirements, then the vibration level may be different.

ATTENTION!

Always use personal hearing protection. 

MAINTENANCE

ATTENTION!

Before starting maintenance and adjustment of the Electrical Rotary Hammer unplug the power cord 
from the power outlet. To ensure quality and safe functioning keep your tool and vents clean at all times. 

 

 If you notice a decrease in impact energy, working tool speed of rotation or extraneous noise, it is necessary to 
hand over the punch to the service center for its repair. 

 

 Working tool maintenance. The use of the worn working tool reduces the effectiveness of the work and may 
result in motor or gearbox failure, so you need to sharpen periodically or replace worn removable tools, as soon 
as there is a need. 

 

 Electric motor care. You must be especially careful with the electric motor, avoid getting liquids and objects 
inside the case. Keep your ventilation holes clean, blow them regularly with compressed air or clean them with 
a brush. When noticeable sparks appear, contact an authorized service center for diagnostics and replacement 
of carbon brushes if necessary.

 

 To prevent dust and grease leakage this Electrical Rotary Hammer has a hermetic design. Therefore, the tool can 

Содержание 26601





























Отзывы: