Denon DN S5000 - DJ Table Top Single CD Player, Руководство по эксплуатации

Страница: 13 / 49

11
ENGLISH
• Each push of the
o
PLAY/PAUSE ( 13 ) button
switches between playback and pause.
PLAY/PAUSE (
13 ) button illuminates solid green
during playback and flashed in pause.
• When the
o
PLAY/PAUSE ( 13 ) button is pushed
during play, the DN-S5000 pauses playback at that
point. Push PLAY/PAUSE (
13 ) button once again
and playback resumes.
• When the Scratch mode is set to MAIN, the Platter
turns when the Main Track is played. When the
rotation of Scratch Disc is stopped by pressing with
the finger, the pause mode is set, and when the
finger is released playback resumes.
5
BASIC OPERATION
Play and pause
1
2
Push the
$2
PITCH/KEY
button to PITCH LED lights up.
• PITCH
→
KEY (key adjust)
→
OFF
Move the
$1
Pitch slider to adjust
the pitch. The current pitch setting
is displayed on the display.
Pitch decreases
Pitch increases
RANGE
PITCH / KEY
• When the
!1
CUE button is pushed during playback,
the track stops and returns to the position that
current playback started (Cue point) and prepares
for next playback. This function is called Back-Cue.
With Back-Cue function, you can start from exactly
same position. The CUE button illuminates solid red
when DN-S5000 is ready to start playback.
• You can set and change Cue point as follows.
• When you started playback.
• Track select finished.
• manual search.
Play and Cue
• If you would not like to start playback from
beginning of the track, you need to move Cue Point
using fast Search and manual search function.
Move the Cue point
1
You can move to the approximate
playback start position by fast-
forwarding and fast-reversing
using the
#1
FAST SEARCH knob.
• With Pitch slider you can adjust the playback speed
(Pitch).
• If you would not change key of sound, use the Key
Adjust function.
Adjusting the pitch
3
DN-S5000 has five pitch ranges,
4%, 10%, 16%, 24% and 100%.
When the
$2
RANGE button
is pushed for more than 1 sec,
the pitch range can be selected
with the PARAMETERS knob. RANGE
PITCH / KEY
4
After you found your
preferred Cue point, push
the
!1
CUE button then new
Cue point is set.
2
Turn the
!4
SCRATCH source
select knob to select Scratch
Disc to search mode. The all
Scratch mode LEDs will turn
off.
3
Turn the
!2
Scratch Disc to
change Cue point. You can hear
the short sound of the current
Cue point.
When Scratch Disc is turned in the pause,
standby or frame repeat mode, works as the
manual search function.
• With PITCH BEND function you can change pitch
temporary. DN-S5000 has three ways for this
function PITCH BEND buttons and Scratch Disc.
Pitch Bend
1
3
[PITCH BEND +/– buttons]
• Push the
#9
PITCH BEND
– or
$0
+ button for
momentary change of
pitch.
While holding these buttons down, the pitch
continues to change up to the limitation.
• After releasing the PITCH BEND buttons,
playback pitch returns to slider setting.
[Scratch Disc]
• When the Scratch mode is
set to SEARCH, the playback
speed can be changed by
turning
!2
Scratch Disc
during playback.
• The pitch increases gradually when the
Scratch Disc is turned clockwise and
decreases when turned counterclockwise.
• When you stop turning the Scratch Disc, the
playing speed returns to the previous pitch.
PITCH BEND
2
When the Scratch source is
set to MAIN and the Platter is
turning, playback of the Main
source can be slowed
temporarily by lightly pressing
!2
Scratch Disc or PLATTER.
In addition, playback can be quickened
temporarily by pushing Scratch Disc or
PLATTER in the direction in which the Platter
is turning.
FAST SEARCH
SEARCH MAIN
SAMP. TRACK
• Turn the
#4
TRACK knob.
• By pushing
#4
TRACK knob down while turning, the
tracks will change 10 at a time.
Select the track
• Normally the BPM for the currently playing track is
measured and displayed on the auto BPM counter.
NOTE:
For some tracks the BPM cannot be measured
properly.
BPM LOCK:
When this button is pressed once while the auto
BPM counter is operating, the data measured by
the auto BPM counter is locked.
TAP:
When you push this button repeatedly, the Auto
mode turns off and starts measuring your Beats Per
Minute (BPM) by tapping.
INPUT BPM:
When the TAP button is pressed and held in for
more than 2 seconds, the BPM input mode is set
and the BPM value can be input directly with the
PARAMETERS knob. When the button is pressed
again, the BPM input mode is turned off.
NOTE:
If you select a new track, AUTO BPM mode turns
on automatically.
BPM