Denison Hydraulics Goldcup 6 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 24

Denison Hydraulics Goldcup 6 Скачать руководство пользователя страница 17

SECTION V – ASSEMBLY PROCEDURES

MOUNTING PORT BLOCK

1. Thread socket pipe plugs (2) into port block.

ASSEMBLY

2. Install O-ring (4) on hollow hex plug (3) and thread the tapped hole in tope of the

See Figure 7

port block.

3. Install gasket (8) on the housing assembly (9).

4. Install the two port plate pins (6) in the face of the port block assembly. Apply petroleum

jelly or heavy grease to the port plate (7) and position port plate over the pins (6) on the

port block.

5. Install the port block assembly and port plate over the end of the auxiliary shaft. Be

certain that tubes 2, 3 and 4 as shown on Fig. 4 are seated and that the port plate (7) is

still on the pins (6).

6. Install the four bolts (5), and torque to 150 ft. lbs.

PARTS LIST FOR FIGURE 7

NO. QTY.

PART NO.

DESCRIPTION

1

1

033-71297

Port block

2

2

431-90404

1/4” Soc. Pipe Plugs

3

1

488-35041

Hollow hex plug SAE-6

4

1

691-00906

O-ring 90-6290-6

5

4

306-40182

Hex head cap screw 5/8-11 x 9

6

2

033-49825

Port plate pins

7

1

033-71531

Port plate M6 only

1

033-71267

Port plate M7 only

8

1

033-70577

Housing gasket

9

1

033-71284

Housing

16

«
...
15
16
17
18
19
...
»

Содержание Goldcup 6

























Отзывы:

Нет отзывов