background image

Introduction 

C-200Air                                                             V16 

Page 1 

Introductions 

 
Congratulations on your purchase of the DEN-SIN

 

High Pressure Cleaner. 

 

Model: C-200AIR 

 

Read this user manual before you start up your High Pressure Cleaner the first time. 

 
This  document  or  part  of  it  may  not  be  photocopied,  or  in  any  other  way  reproduced,  or 
translated to other languages without the prior written consent of 

DEN-SIN

 
This machine is a High Pressure Cleaner producing water jet under high-pressure, which is 
why severe injuries can occur if the safety precautions are not observed. 
Therefore a full understanding of the contents of this instruction manual is required, in order 
to prevent injuries to you, objects and persons near-by. 

 

Safety 

The  following  symbols  are  used  in  this  manual  to  indicate  procedures  that  if  not  followed, 
may results in personal injuries or damage to equipment. 

 

 

 
 
 
 
               

 

         

 
 
 
 
 
 
 
 
 
 
Version 16: March 2015 

 

Revision History 

 

Revision 

Rev.No. 

Manual updating 

14 

Manual Updating / Repair Kit Updating 

15 

Updating of Manual with new configuration components 

16 

 

 

 

 

 

WARNING

 

is  used  to  alert  the  reader  of  procedures  or 

practice which if not followed correctly could result in personal 
injuries.   

WARNING 

CAUTION 

CAUTION

  is  used  to  alert  the  reader  of  procedures  or 

practice which if not followed correctly could result in damage 
to machine or other equipment. 

NOTE

  is  used  to  highlight  important  information  that  may 

assist the reader carrying out the procedure or understanding the 
text. 

NOTE 

Содержание C-200AIR



































Отзывы: