Delta 62 TP3 Series Скачать руководство пользователя страница 18

Delta Commercial Faucet Limited Warranty

All parts of the Delta® HDF® and TECK® faucets are warranted to the original consumer purchaser to be free from defects in material, finish 
and workmanship for a period of five (5) years unless otherwise specifically stated in the catalogue and price book.  This warranty is made to 
the original consumer purchaser and shall be effective from date of purchase as shown on purchaser’s receipt.

Delta will, at its option, repair or replace, FREE OF CHARGE, during the warranty period, any part which proves defective in material or 
workmanship under normal installation, use and water and service conditions.  If Delta Faucet concludes that the returned part was 
manufactured by Delta Faucet and is, in fact, defective, then Delta Faucet will honour the warranty stated herein.  Replacement parts can be 
obtained from your local dealer or distributor listed in the telephone directory or by returning the part along with the purchaser’s receipt to 
our factory, TRANSPORTATION CHARGES PREPAID, at the address listed.  THIS WARRANTY IS THE ONLY EXPRESS WARRANTY MADE BY DELTA.  
ANY CLAIMS MADE UNDER THIS WARRANTY MUST BE MADE DURING THE FIVE YEAR PERIOD REFERRED TO ABOVE.  ANY IMPLIED WARRAN-
TIIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 
THE DURATION OF THIS WARRANTY.  LABOUR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION, REPAIR OR REPLACEMENT AS WELL 
AS INCIDENTAL AND CONSEQUENTIAL, SPECIAL, INDIRECT OR PUNITIVE DAMAGES CONNECTED THEREWITH ARE EXCLUDED AND WILL NOT 
BE PAID BY DELTA FAUCET.

Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential 
damages, so the above limitations or exclusions may not apply to you.  This warranty gives you specific legal rights, and you may also have 
other rights which vary from state to state.

This warranty is for commercial products only from Delta Faucet Company and Delta Faucet Canada (a division of Masco Canada Limited) 
and is void for any damage to this faucet due to misuse, abuse, neglect, accident, improper installation, any use in violation of instructions 
furnished by Delta Faucet or any use of replacement parts other than genuine Delta parts.

Delta Faucet Canada, a division of Masco Canada Limited

350 South Edgeware Road, St. Thomas, Ontario, N5P 4L1

1-800-567-3300 (English)    1-800-265-9245 (French)

Delta Faucet Company

Box 40980, 55 East 111th St., Indianapolis, IN, U.S.A. 46280

(317) 848-1812

www.deltacommercialfaucets.com

Page 18

209989   Rev. B

For further technical assistance, call Delta Commercial Technical Service at 1-800-387-8277 (Canada) or 1-877-509-2680 (U.S.A.).

This device complies with Part 15 of the FCC Rules.  Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and 

(2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.  These limits

are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This 

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may 

cause harmful interference to radio communications.  Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

Warning:

Changes or modifications not expressly approved by Delta could void the user’s authority to operate the equipment.

CAN ICES-3 (A) / NMB-3(A)  

    

 

 

 

 

 

© 2016 Masco Corporation of Indiana

Содержание 62 TP3 Series



















Отзывы: