Delphi EZ-Pro 15-6 Kiln страница 37 Скачать руководство пользователя | Manualshive

Страница: 37 / 55

background image

37

Press (Decrease) button to select the firing program and once selected the LED light
beside “Review” will light up. Additionally, the firing program selected will

begin to

display on the LED display beginning with

rA 1

. Once the review has been completed,

the display will show

Strt

.

Press (Program) button and the display will show

–On-

and begin firing. Note: If you

accidentally selected the wrong program or would like to stop the program, press
(Program) button again and the display will show

Stop.

Once the kiln has completed firing, the display will show

CPLt

and this message will

alternate with the temperature display and the total firing time from start to finish. DO
NOT open the kiln until it has completely cooled and the temperature shows room
temperature.

«
...
35
36
37
38
39
...
»

Содержание EZ-Pro 15-6 Kiln
























































Отзывы:

Нет отзывов

Похожие инструкции для EZ-Pro 15-6 Kiln

Бренд: Samson Страницы: 56

Бренд: Hach Страницы: 128

Бренд: Yamato Страницы: 33

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Бренд: OJ Electronics Страницы: 8

Бренд: OJ Electronics Страницы: 112

Бренд: OJ Страницы: 17

Бренд: Quinny Страницы: 29

Бренд: Quinny Страницы: 60

Бренд: Maximum Controls Страницы: 58

Бренд: Pfeiffer Vacuum Страницы: 100

Бренд: Festo Страницы: 62

Бренд: Woodward Страницы: 32

Бренд: Hunter Страницы: 2

Бренд: jablotron Страницы: 12

Бренд: FuzzDog Страницы: 9

Universal Family for Sony

Бренд: Jolly Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды