manualshive.com logo in svg

Delphi EZ-Pro 15-6 Kiln, Руководство пользователя, Страница: 27 / 55

Поделиться
Скачать
Delphi EZ-Pro 15-6 Kiln Скачать руководство пользователя страница 27

 

27 

3.  When power is restored, the temperature drop during the power 

interruption must be less than 72ºF (40ºC). If not, the display will show the 
alarm code 

PF 3

 and terminate the firing. 

Status Display Codes

 

Below is a list of normal display codes which indicate the controller mode of 
operation. 
 

IdLE 

- This is ready mode; No firing in process. This message will alternate with 

the temperature display and/or any alarm messages that may occur. 
 

dELA

  - This is the delay start mode. This message will alternate with the delay 

time count-down if programmed. 
 

Strt

 

- This is a final prompt before starting a new firing. The Delay start and 

thermocouple offset features are accessed from this prompt. 
 

-On- 

- This is a short (5 second) display that indicates a new firing has been 

started. 
 

StOP

  - This is an Abort message; the firing was stopped early. This message 

will alternate with the temperature display and/or any alarm messages that may 
occur. 
 

CPLt

  - This is a firing complete message; the firing ended successfully. This 

message will alternate with the temperature display and the total firing time from 
start to finish. 
 

-90-, -96-, bEAd, CLA, USr   

-

 

This is a short (5 second) display of the Program 

Mode  which appears every time the controller is turned on. 

 

 

 

Alarm Display Codes 

In addition to Power failure alarms, these messages may be displayed if the 
controller detects a problem during the firing. 
 

tC

    - This alarm will appear when the kiln is idle and indicates that the 

thermocouple sensor is no longer detected. The controller can not operate 
without a thermocouple signal. In most cases, the thermocouple has failed and 
will need replacement, or the electrical connections for the thermocouple may be 
loose or damaged. Check the wiring for the thermocouple and the physical 
condition of the probe inside the firing chamber. 
 

tCr

    - This alarm indicates that the thermocouple sensor is detected but the 

signal is reversed. The firing was terminated. The thermocouple signal is a low 
voltage direct current with +/- polarity. The controller will sense that the 
temperature is traveling backwards from what is expected. In most cases, this 
indicates that the thermocouple needs to be reconnected properly. Check the 
wiring for the thermocouple. 
 

Содержание EZ-Pro 15-6 Kiln
























































Отзывы:

Нет отзывов