7
A19. Infuser door
A20. Infuser
A21. Power cord
A22. Main switch
3.2 Description of the touch screen
(page 3 - B )
A number of buttons on the panel have a dual function. This is
indicated in brackets in the description.
B1. Display: guides the user in using the appliance. The current
selection is at the center between two dotted lines.
B2.
▼
Selection arrow
(“ESC”: when programming beverages,
press to exit without saving the change)
B3.
OK
: to confirm the selection
(During the first few seconds of
"espresso", "ristretto" or "Lungo" delivery, press for 2 cups)
B4.
▲
Selection arrow
(“STOP” - When delivering/program-
ming beverages, press to interrupt/programme)
B5.
/ESC: to perform a rinse cycle.
(When in the settings menu, it acts as the "ESC" button to exit
from the selected function and go back to the main menu)
B6.
: appliance settings menu
B7.
: aroma selection
Directly selected beverages:
B8.
: Espresso
B9.
: TrueBrew Over Ice
(TM)
Coffee
B10.
: Long
B11.
: Cappuccino
B12. : Latte
B13. : Hot Milk
B14.
: Select additional beverages available from
the Drink Menu: Lungo, Ristretto, Double E, Cap-
, Cappuccino Mix, Latte Macchiato, Flat White,
Espresso Macchiato, 2 Espresso, 2 Ristretto, 2 Lungo, Hot
Water
B15.
: Customize and select recipes from the My
Menu. Beverages on the My Menu are automatically set to
default settings, until customized.
3.3 Description of the accessories
(page 3 - C )
C1. Water hardness indicator paper
C2. Pre-ground coffee measure
C3. Descaler
C4. Water softener filter (certain models only)
C5. Cleaning brush
C6. Hot water spout
3.4 Description of the milk container
(page 3 - D )
D1. Froth adjustment and CLEAN dial
D2. Milk container lid
D3. Milk container
D4. Milk intake tube
D5. Frothed milk spout (adjustable)
4. BEFORE USE
4.1 Checking the appliance
After removing the packaging, make sure the product is com-
plete and undamaged and that all accessories (C) are pres-
ent. Do not use the appliance if it is visibly damaged. Contact
De’Longhi Customer Services.
4.2 Installing the appliance
Important!
When you install the appliance, you should respect the follow-
ing safety warnings:
• The machine gives off heat. After positioning the machine
on the worktop, leave a space of at least 1.18 in / 3 cm be-
tween the surfaces of the machine and the side and rear
walls and at least 5.6 in / 15 cm above the coffee maker.
• Water penetrating the machine could cause damage.
Do not place the appliance near taps or sinks.
• The appliance could be damaged if the water it contains
freezes.
Do not install the appliance in a room where the tempera-
ture could drop below freezing point.
• Arrange the cord (C7) in such a way that it cannot be dam-
aged by sharp edges or come with contact with hot surfac-
es (e.g. electric hot plates).
4.3 Connecting the appliance
Important!
Check that the mains power supply voltage corresponds to that
indicated on the rating plate on the bottom of the appliance.
Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10A only.
If the power socket does not match the plug on the appliance,
have the socket replaced with a suitable type by a qualified
professional.
4.4 Setting up the appliance
Please note:
• Coffee has been used to factory test the appliance and it is
therefore completely normal for there to be traces of coffee
in the grinder. The machine is, however, guaranteed to be
new.
• You should customise water hardness as soon as possible
following the instructions in section “16.2 Setting water
hardness”.
