Dell Vostro 3555 Скачать руководство пользователя страница 103

Страница: 103 / 116

Diagnostics

Device Status Lights

Turns on when you turn on the computer and blinks when the computer is in a
power management mode.

Turns on when the computer reads or writes data.

Turns on steadily or blinks to indicate battery charge status.

Turns on when wireless networking is enabled.

Battery Status Lights

If the computer is connected to an electrical outlet, the battery light operates as

follows:

• Alternately blinking amber light and white light — An unauthenticated or

unsupported non-Dell AC adapter is attached to your laptop.

• Alternately blinking amber light with steady white light — Temporary battery

failure with AC adapter present.

• Constantly blinking amber light — Fatal battery failure with AC adapter

present.

• Light off — Battery in full charge mode with AC adapter present.
• White light on — Battery in charge mode with AC adapter present.

Diagnostic Beep Codes

The following table shows the possible beep codes that may be emitted by the

computer when your computer is unable to complete a power on self test.

Beep

Possible Cause

Troubleshooting Steps

BIOS ROM checksum in
progress of failure.

System board failure,
covers BIOS corruption or
ROM error

103

Содержание Vostro 3555





















































































































Результаты поиска

Содержание Vostro 3555

Отзывы:

Похожие инструкции для Vostro 3555

Бренды по названию

Популярные бренды

Dell Vostro 3555, Руководство пользователя

Результаты поиска

Содержание Vostro 3555

Отзывы:

Похожие инструкции для Vostro 3555

Бренды по названию

Популярные бренды