Dell Precision M4800 Скачать руководство пользователя страница 27

Страница: 27 / 83

Installing the Processor Fan

Connect the processor-fan cable.

NOTE: Ensure that the processor-fan cable does not protrude outside its compartment.

Insert the processor fan into its slot in the computer.

Tighten the screws that secure the processor fan to the computer.

Install the:
a) base cover
b) battery

Follow the procedures in

After Working Inside Your Computer

Removing the Video-Card Fan

Follow the procedures in

Before Working Inside Your Computer

Remove the:
a) battery
b) base cover

Perform the following steps to remove the video-card fan.
a) Disconnect the video-card fan cable.
b) Remove the screws that secure the video-card fan to the computer.
c) Remove the video-card fan from the computer.

Содержание Precision M4800




















































































Результаты поиска

Содержание Precision M4800

Отзывы:

Похожие инструкции для Precision M4800

Бренды по названию

Популярные бренды

Dell Precision M4800, Руководство пользователя

Результаты поиска

Содержание Precision M4800

Отзывы:

Похожие инструкции для Precision M4800

Бренды по названию

Популярные бренды