Dell PowerConnect B-FCX Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 152

background image

PowerConnect B-Series FCX Web Management Interface User Guide

45

53-1002268-01

Monitoring RMON statistics

3

Monitoring RMON statistics

RMON statistics provides count information on multicast and broadcast packets. This information
includes total packets sent, undersized and oversized packets, CRC alignment errors, jabbers,
collisions, fragments, and dropped events for each port on the system. RMON statistics collection
is activated automatically during system startup, and requires no configuration.

Packets: Broadcast

The total number of good packets received that were directed to the broadcast
address.
This number does not include multicast packets.

Packets: Multicast

The total number of good packets received that were directed to a multicast address.
This number does not include packets directed to the broadcast address.

CRC Alignment Errors

The total number of packets received that were from 64 – 1518 octets long, but had
either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment Error).
The packet length does not include framing bits but does include FCS octets.

Size Packets: Under

The total number of packets received that were less than 64 octets long and were
otherwise well formed.
This number does not include framing bits but does include FCS octets.

Size Packets: Over

The total number of packets received that were longer than 1518 octets and were
otherwise well formed.
This number does not include framing bits but does include FCS octets.

Fragments

The total number of packets received that were less than 64 octets long and had
either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment Error).
It is normal for this counter to be incremented, since it counts both runts (which are
normal occurrences due to collisions) and noise hits.
This number does not include framing bits but does include FCS octets.

Jabbers

The total number of packets received that were longer than 1518 octets and had
either a bad FCS with an integral number of octets (FCS Error) or a bad FCS with a
non-integral number of octets (Alignment Error).
NOTE: This definition of jabber is different from the definition in IEEE-802.3 section

8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define
jabber as the condition where any packet exceeds 20 ms. The allowed range to
detect jabber is between 20 ms and 150 ms.

This number does not include framing bits but does include FCS octets.

Collisions

The best estimate of the total number of collisions on this Ethernet segment.

«
...
53
54
55
56
57
...
»

Содержание PowerConnect B-FCX

























































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerConnect B-FCX

Бренд: Magnetrol Страницы: 12

Бренд: Magnetrol Страницы: 24

Бренд: Little Giant Страницы: 2

Бренд: SIIG Страницы: 17

Бренд: LEGRAND Страницы: 30

PFS4226-24ET-240

Бренд: Dahua Страницы: 3

Бренд: DeLOCK Страницы: 26

Бренд: Enterasys Страницы: 41

Бренд: ZIMCO Страницы: 7

Бренд: Goobay Страницы: 2

Бренд: DVIGear Страницы: 11

AVS-OP-2416-340

Бренд: AMX Страницы: 1

Luzense RADIM RF

Бренд: Unilamp Страницы: 2

AMX DVX-2265-4K

Бренд: Harman Страницы: 2

Thinklogical TLX640

Бренд: Belden Страницы: 48

Бренд: H3C Страницы: 8

PDU-ATS-100A-208Y.120-3PH

Бренд: Larson Electronics Страницы: 14

Бренд: MyQ Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды