Dell Inspiron 9300 Скачать руководство пользователя

Страница: 38 / 60

Back to Contents Page

USB Port Board

Dell™ Inspiron™ 9300 Service Manual

Removing the USB Port Board

Replacing the USB Port Board

Removing the USB Port Board

Follow the instructions in "

Before Working Inside Your Computer

Remove the

hinge cover

Remove the

keyboard

Remove the

display assembly

Remove the

palm rest

Disconnect the USB-port-board cable connector from the system board.

Remove the M2.5 x 5-mm screw, and lift the board up and out of the computer.

Replacing the USB Port Board

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must

remove the main battery

before you begin working inside the computer.

USB port board

M2.5 x 5-mm screw

notch

USB-port-board cable

system board connector

tab

Содержание Inspiron 9300





























































Результаты поиска

Содержание Inspiron 9300

Отзывы:

Похожие инструкции для Inspiron 9300

Бренды по названию

Популярные бренды

Dell Inspiron 9300, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 9300

Отзывы:

Похожие инструкции для Inspiron 9300

Бренды по названию

Популярные бренды