Dell Inspiron 9300 Скачать руководство пользователя

Страница: 12 / 60

Back to Contents Page

Modem

Dell™ Inspiron™ 9300 Service Manual

Removing the Modem

Replacing the Modem

Removing the Modem

Follow the instructions in "

Before Working Inside Your Computer

Turn the computer over, loosen the two captive screws on the modem cover, and remove the cover from the computer.

Remove the M2 x 3-mm screw that attaches the modem to the system board.

Pull up on the pull-tab to disconnect the modem from the connector on the system board.

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must

remove the main battery

before you begin working inside the computer.

NOTICE:

1 modem

2 modem cable

3 pull-tab

4 M2 x 3-mm screw

Содержание Inspiron 9300





























































Результаты поиска

Содержание Inspiron 9300

Отзывы:

Похожие инструкции для Inspiron 9300

Бренды по названию

Популярные бренды

Dell Inspiron 9300, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 9300

Отзывы:

Похожие инструкции для Inspiron 9300

Бренды по названию

Популярные бренды