Dell Inspiron 9300 Скачать руководство пользователя | Manualshive

Страница: 19 / 60

background image

Back to Contents Page

Hinge Cover

Dell™ Inspiron™ 9300 Service Manual

Removing the Hinge Cover

Replacing the Hinge Cover

Removing the Hinge Cover

1.

Follow the instructions in "

Before Working Inside Your Computer

."

2.

Open the display all the way (180 degrees) so that it lies flat against your work surface.

3.

Using a small flat-blade screwdriver, insert the screwdriver on the right side to gently pry the hinge cover loose.

4.

Pulling up from right to left, remove the hinge cover.

5.

Disconnect your computer and all attached devices from their electrical outlets.

Replacing the Hinge Cover

With the display open all the way (180 degrees) so that it lies flat against the work surface, snap the cover back into place, starting from left to right.

Back to Contents Page

CAUTION:

Before you begin the following procedure, see the safety instructions in the

Product Information Guide

.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

To avoid damaging the system board, you must

remove the main battery

before you begin working inside the computer.

NOTICE:

The hinge cover is fragile and can be damaged if extreme force is used. Be careful when removing the hinge cover.

1 hinge cover

«
...
17
18
19
20
21
...
»

Содержание Inspiron 9300





























































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 9300

Fieldmate Series

Бренд: InfoCase Страницы: 4

Бренд: Palm Страницы: 11

Бренд: Asus Страницы: 28

Бренд: Asus Страницы: 23

Disney Netpal MK90H

Бренд: Asus Страницы: 68

Бренд: Asus Страницы: 20

Бренд: Asus Страницы: 112

Бренд: Asus Страницы: 96

Бренд: Asus Страницы: 104

C213NA-BW0034-OSS

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 102

Бренд: Asus Страницы: 128

Бренд: Asus Страницы: 98

Бренд: Asus Страницы: 102

Бренд: Asus Страницы: 122

C200M Chromebook

Бренд: Asus Страницы: 88

Chromebook C423NA

Бренд: Asus Страницы: 92

Бренд: Asus Страницы: 160

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды