Dell G5 15 Скачать руководство пользователя

Страница: 109 / 112

NOTE:

Some tests for specific devices require user interaction. Always ensure that you are present at the computer terminal

when the diagnostic tests are performed.

For more information, see

Dell EPSA Diagnostic 3.0

Running the ePSA diagnostics

Turn on your computer.

As the computer boots, press the F12 key as the Dell logo appears.

On the boot menu screen, select the

Diagnostics

option.

Click the arrow at the bottom left corner.
Diagnostics front page is displayed.

Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.

To run a diagnostic test on a specific device, press Esc and click

Yes

to stop the diagnostic test.

Select the device from the left pane and click

Run Tests

If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.

System diagnostic lights

Power and battery-status light/hard-drive activity light

Indicates the battery-charge status or the hard-drive activity.

NOTE:

Press Fn+H to toggle this light between power and battery-status light and hard-drive activity light.

Hard-drive activity light

Turns on when the computer reads from or writes to the hard drive.

NOTE:

Hard-drive activity light is supported only on computers shipped with hard drive.

Power and battery-status light

Indicates the power and battery-charge status

Solid white

— Power adapter is connected and the battery has more than 5 percent charge.

Amber

— Computer is running on battery and the battery has less than 5 percent charge.

Off

•

Power adapter is connected and the battery is fully charged.

•

Computer is running on battery and the battery has more than 5 percent charge.

•

Computer is in sleep state, hibernation, or turned off

The power and battery-status light blinks amber along with beep codes indicating failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by
a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.

The following table shows different light patterns and describes what they indicate.

Troubleshooting

109

Содержание G5 15

















































































































Результаты поиска

Содержание G5 15

Отзывы:

Похожие инструкции для G5 15

Бренды по названию

Популярные бренды

Dell G5 15, Руководство по обслуживанию

Результаты поиска

Содержание G5 15

Отзывы:

Похожие инструкции для G5 15

Бренды по названию

Популярные бренды