Dell EMC VxFlex Ready Node Скачать руководство пользователя страница 62

Страница: 62 / 92

Figure 27 Installing the front end of the rail

Repeat the preceding steps to install the right rail assembly.

Secure the rail assemblies to the cabinet

The supplied screws and washers are used to secure the rail assemblies to the front and rear of the cabinet.

About this task

Note:

For square hole cabinets, install the supplied conical washer before installing the screw. For unthreaded

round hole cabinets, install only the screw without the conical washer.

Procedure

Align the screws with the designated U spaces on the front and rear rack flanges.

Ensure that the screw holes on the tab of the system retention bracket are seated on the designated U spaces.

Insert and tighten the two screws using the Phillips #2 screwdriver.

Figure 28 Installing screws

R740XD Configuration Equipment Installation

Dell EMC VxFlex Ready Node Server Installation Guide

Содержание EMC VxFlex Ready Node





























































































Результаты поиска

Содержание EMC VxFlex Ready Node

Отзывы:

Похожие инструкции для EMC VxFlex Ready Node

Бренды по названию

Популярные бренды

Dell EMC VxFlex Ready Node, Руководство по установке

Результаты поиска

Содержание EMC VxFlex Ready Node

Отзывы:

Похожие инструкции для EMC VxFlex Ready Node

Бренды по названию

Популярные бренды