Dell Alienware M17X R3 Скачать руководство пользователя страница 64

Страница: 64 / 110

WirelessHD Card (Optional)

Replacing the WirelessHD Card

Follow the instructions in "Before You Begin" on page 9.

Remove the new wirelessHD card from its packaging.

CAUTION:

Use firm and even pressure to slide the card into place. If you use

excessive force, you may damage the connector.

CAUTION:

The connectors are keyed to ensure correct insertion. If you feel

resistance, check the connectors on the card and on the system board, and realign
the card.

Insert the wirelessHD card connector at a 45-degree angle into the

connector on the system board.

Press the other end of the wirelessHD card down into the slot on the

system board and replace the screw that secures the wirelessHD card to the

system board.

Connect the wirelessHD card cable to the connector on the wirelessHD

card.

Replace the keyboard (see "Replacing the Keyboard" on page 57).

wirelessHD card cable

wirelessHD card

screw

Содержание Alienware M17X R3















































































































Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды

Dell Alienware M17X R3, Руководство по обслуживанию

Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды