Dell Alienware M17X R3 Скачать руководство пользователя страница 103

Страница: 103 / 110

System Setup

103

Advanced Menu

Intel SpeedStep

Allows you to enable or disable the Intel

SpeedStep technology. Disabling this

feature may improve performance, but

will greatly reduce battery life.

Virtualization

Allows you to enable or disable the Intel

Virtualization technology.

USB Emulation

Allows you to enable or disable the USB

emulation feature. This feature defines

how the BIOS, in the absence of a

USB-aware operating system, handles

USB devices. USB emulation is always

enabled during POST.

NOTE:

You cannot boot any type of USB

device (floppy, hard drive, or memory key)

when this option is off.

USB Wake Support

Allows you to enable USB devices to wake

the computer from standby or to disable

the USB wake support feature.

NOTE:

If USB Powershare is enabled, a

device connected to the USB Powershare

connector may not wake the computer.

USB Power Share

Allows you to charge USB devices when

the computer is turned off or in standby

mode.

• AC Only: Charge USB devices when

connected to AC adapter only.

• AC and Battery: Charge USB devices

when connected to AC adapter and

when the computer is running on

battery.

• Disabled: Disables USB PowerShare.

Содержание Alienware M17X R3















































































































Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды

Dell Alienware M17X R3, Руководство по обслуживанию

Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды