Dell Alienware M17X R3 Скачать руководство пользователя страница 13

Страница: 13 / 110

Battery Pack

Battery Pack

WARNING:

Before working inside your computer, read the safety information

that shipped with your computer. For additional safety best practices information,
see the Regulatory Compliance Homepage at
www.dell.com/regulatory_compliance.

CAUTION:

To avoid electrostatic discharge, ground yourself by using a wrist

grounding strap or by periodically touching an unpainted metal surface (such as a
connector on your computer).

CAUTION:

Only a certified service technician should perform repairs on your

computer. Damage due to servicing that is not authorized by Dell is not covered by
your warranty.

CAUTION:

To avoid damage to the computer, use only the battery designed for

this particular Alienware computer. Do not use batteries designed for other
Alienware computers.

Removing the Battery Pack

Follow the instructions in "Before You Begin" on page 9.

Shut down the computer and turn it over.

Slide the battery latch to the unlock position as shown.

The battery pack pops up.

Remove the battery pack.

Содержание Alienware M17X R3















































































































Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды

Dell Alienware M17X R3, Руководство по обслуживанию

Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды