Dell Alienware M17X R3 Скачать руководство пользователя страница 105

Страница: 105 / 110

System Setup

105

Adapter Warnings

• Allows you to choose if the

computer should display warning

messages when you use AC

adapters that are not supported

by your computer.

• Enabled: BIOS will detect

unsupported AC adapters and

display an error on the screen.

Charger Behavior

Allows you to enable or disable battery

charging.

Advanced Menu—Performance Options

Overclocking Feature

Allows you to enable or disable the global

overclocking feature.

• Disabled: The overclocking feature is

disabled.

• Enabled: Displays additional

overclocking options.

Override Turbo settings

Allows you to override CPU turbo mode

settings.

Long Duration PWR Limit

Allows you to set the turbo mode power

limit 1 value in watts.

Long Duration Time Window

Allows you to set the turbo mode time 1

value in seconds.

Set Short Duration PWR Limit

Allows you to enable or disable short

duration power limit.

Set Short Duration PWR Limit

Allows you to set the turbo mode power

limit 2value in watts.

Bus Clock

Current Frequency

Displays the current bus clock frequency.

New Frequency in 10KHz

increments

Allows you to set the bus clock frequency

in increments of 10KHz.

Apply New Bus Clock Frequency

Applies the new bus clock frequency

immediately, temporarily, or permanently.

Memory Overclocking

Содержание Alienware M17X R3















































































































Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Dell Alienware M17X R3, Руководство по обслуживанию, Страница: 105 / 110

Результаты поиска

Содержание Alienware M17X R3

Отзывы: