Dell Alienware M17X R3 Скачать руководство пользователя страница 42

Страница: 42 / 110

Processor Heat-Sink

Replacing the Processor Heat-Sink

CAUTION:

Incorrect alignment of the processor heat-sink can damage the

processor.

NOTE:

The original thermal grease can be reused if the original processor

heat-sink is reinstalled. If the processor heat-sink is replaced, use the thermal

grease provided in the kit to ensure that thermal conductivity is achieved.

Follow the instructions in "Before You Begin" on page 9.

Slide the processor heat-sink in place.

Align the four captive screws on the processor heat-sink with the screw

holes on the system board and tighten the screws in sequential order

(indicated on the processor heat-sink).

Replace the processor heat-sink fan (see "Replacing the Processor

Heat-Sink Fan" on page 38).

Replace the compartment door (see "Replacing the Compartment Door"

on page 16).

processor heat-sink

captive screws (4)

Содержание Alienware M17X R3















































































































Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды

Dell Alienware M17X R3, Руководство по обслуживанию

Результаты поиска

Содержание Alienware M17X R3

Отзывы:

Похожие инструкции для Alienware M17X R3

Бренды по названию

Популярные бренды