Dell 6 series Скачать руководство пользователя страница 85

Страница: 85 / 160

Configuring and Managing RAID

Virtual Disk Management

Creating Virtual Disks

NOTE:

Combining SAS and SATA hard disk drives (HDDs) within a virtual disk is not

supported. Also, combining HDDs and Solid State Drives (SSDs) within a virtual disk
is not supported.

Perform the following steps to create virtual disks.

During host system bootup, press <Ctrl><R> when the BIOS banner
displays.
The

Virtual Disk Management

screen displays. If there is more than one

controller, the main menu screen displays. Select a controller, and press
<Enter>. The

Virtual Disk Management

screen displays for the selected

controller.

NOTE:

This procedure describes the BIOS Configuration Utility screens in

Tree View.

Read Policy

Read-Ahead

enables the read ahead feature for the virtual disk.

You can set this parameter to

Read-Ahead

No-Read-Ahead

, or

Adaptive

. The default is

No-Read-Ahead

Read-Ahead

specifies that the controller uses

Read-Ahead

for

the current virtual disk.

Read-Ahead

capability allows the

controller to read sequentially ahead of requested data and
store the additional data in cache memory, anticipating that
the data is required soon.

No-Read-Ahead

specifies that the controller does not use read

ahead for the current virtual disk.

NOTE:

No-Read-Ahead

shows higher performance results due to

the effectiveness of hard-drive caching algorithms.

Adaptive

specifies that the controller begins using

Read-Ahead

if the two most recent disk accesses occurred in sequential
sectors. If all read requests are random, the algorithm reverts to

No-Read-Ahead

; however, all requests are still evaluated for

possible sequential operation.

Table 6-2.

Virtual Disk Parameters and Descriptions

(continued)

Parameter

Description

Dell_PERC6.2_UG.book Page 85 Wednesday, June 24, 2009 6:08 PM

Содержание 6 series

































































































































































Результаты поиска

Содержание 6 series

Отзывы:

Похожие инструкции для 6 series

Бренды по названию

Популярные бренды

Dell 6 series, Руководство пользователя

Результаты поиска

Содержание 6 series

Отзывы:

Похожие инструкции для 6 series

Бренды по названию

Популярные бренды