Dell 6 series Скачать руководство пользователя страница 59

Страница: 59 / 160

Installing and Configuring Hardware

Removing and Installing the PERC 6/i and
CERC 6/i Integrated Storage Controller Cards in
Dell Modular Blade Systems (Service-Only
Procedure)

CAUTION:

Electrostatic discharge can damage sensitive components.

Always use proper antistatic protection when handling components.
Touching components without using a proper ground can damage the equipment.

The storage controller card is located below the hard drive bays of the
Dell Modular Blade system. To remove the storage controller card:

Remove the Dell Modular Blade system from the Modular Blade
system chassis. For more information on removing the blade system from
the Modular Blade system chassis, see your system’s

Hardware Owner’s

Manual or the User’s Guide

Remove the system cover of the Modular Blade system. For more
information on opening the top cover of the Modular Blade system,
see your system’s

Hardware Owner’s Manual or the User’s Guide

Remove the system board and place it on a stable and flat surface.
For more information on removing the system board, see your system’s

Hardware Owner’s Manual or the User’s Guide

Open the release lever to disconnect the storage controller card edge
connector from the system board connector as illustrated in Figure 4-14.

Lift the storage controller card straight up from the system board as
illustrated in Figure 4-14.

CAUTION:

Applying pressure to the internal SAS port connectors may

damage them.

Dell_PERC6.2_UG.book Page 59 Wednesday, June 24, 2009 6:08 PM

Содержание 6 series

































































































































































Результаты поиска

Содержание 6 series

Отзывы:

Похожие инструкции для 6 series

Бренды по названию

Популярные бренды

Dell 6 series, Руководство пользователя

Результаты поиска

Содержание 6 series

Отзывы:

Похожие инструкции для 6 series

Бренды по названию

Популярные бренды