Dell 6 series Скачать руководство пользователя страница 54

Страница: 54 / 160

Installing and Configuring Hardware

Figure 4-10.

Removing the TBBU

Disconnecting the BBU from a PERC 6/i Adapter
or a PERC 6/i Integrated Controller

NOTE:

A PERC 6/i adapter installed in a Dell workstation or a Dell PowerEdge SC

system does not have a BBU.

NOTE:

Batteries with low charges can be detected and recharged. The battery must

first be charged and the system must be restarted for the battery to be active again.

This section describes how to disconnect the BBU on a PERC 6/i adapter or a
PERC 6/i Integrated controller while the adapter or controller is installed in a
system.

NOTE:

The location of the PERC 6/i varies from system to system. For information on

PERC 6/i card location, see the

Hardware Owner’s Manual

shipped with your

system or on the Dell Support website at

support.dell.com

NOTE:

For more information on removing and replacing parts, see the

Hardware

Owner’s Manual

shipped with your system or on the Dell Support website at

support.dell.com

memory module

battery

Dell_PERC6.2_UG.book Page 54 Wednesday, June 24, 2009 6:08 PM

Содержание 6 series

































































































































































Результаты поиска

Содержание 6 series

Отзывы:

Похожие инструкции для 6 series

Бренды по названию

Популярные бренды

Dell 6 series, Руководство пользователя

Результаты поиска

Содержание 6 series

Отзывы:

Похожие инструкции для 6 series

Бренды по названию

Популярные бренды