Dell EMC MXG610s Скачать руководство пользователя страница 34

Страница: 34 / 45

Technical specifications

This section highlights the features and specifications for the Dell EMC MXG610s 32 Gbps FC switch module.

System specifications

Table 6. System specifications

System components

Description

Enclosure

Less than 1U module—2.75 cm / 1.08 inches

Power inlet

Internal to the chassis

Power supplies

12 V power supply from the Dell EMC PowerEdge MX7000 chassis

3.3 V standby power supply derived from 12 V source on the switch

module

Maximum power—150 Watts

Fans

Internal to the chassis

Cooling

Integrated system cooling; back-to-front port-side exhaust

System architecture

Nonblocking shared memory switch

System processors

Freescale PowerPC T1022E with two cores at 1.2 GHz

Table 7. Fibre Channel specifications

System components

Description

Fibre Channel ports

Default switch mode

•

16 external ports supporting 8 Gbps, 16 Gbps, and 32 Gbps

speeds using eight SFPs and two QSFPs

•

16 internal ports supporting 16 Gbps and 32 Gbps speeds

ANSI Fibre Channel protocol

Fibre Channel Physical and Signaling Interface standard—FC-PH

Modes of operation

Fibre Channel Class 2, Class 3, and Class F

Fabric initialization

Complies with FC-SW-5

FCIP—IP over Fibre Channel

Complies with FC-IP 2.3 of FCA profile

Port status

Bicolor LED—amber/green

Technical specifications

Содержание MXG610s














































Результаты поиска

Содержание MXG610s

Отзывы:

Похожие инструкции для MXG610s

Бренды по названию

Популярные бренды

Dell EMC MXG610s, Руководство по установке

Результаты поиска

Содержание MXG610s

Отзывы:

Похожие инструкции для MXG610s

Бренды по названию

Популярные бренды