Deep Sea Electronics Plc DSE5110 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 54

background image

12

Part No. 057-009 5110 Operating Manual Issue 3.3 3/1/2006

5.1 WARNINGS

Warnings are non-critical alarm conditions and do not affect the operation of the generator system, they
serve to draw the operators attention to an undesirable condition.

In the event of a warning alarm the LCD will display:-

BATTERY CHARGE FAILURE

, if the module does not detect a voltage from the warning light terminal on

the auxiliary charge alternator the

icon will illuminate.

FAIL TO STOP,

If the module detects the engine is still running when the ‘Fail to stop timer’ expires, then

the module will display:-

NOTE:- ‘Fail to Stop’ could indicate a faulty oil pressure sender - If engine is at rest check oil

sender wiring and configuration.

AUXILIARY INPUTS

, if an auxiliary input has been configured as a warning the appropriate LCD

segment will be displayed:-

!

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

«
...
10
11
12
13
14
...
»

Содержание DSE5110























































Отзывы:

Нет отзывов

Похожие инструкции для DSE5110

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: NCR Страницы: 6

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 45

Бренд: Panasonic Страницы: 24

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Cansec Страницы: 45

Бренд: Cansec Страницы: 43

Бренд: Cansec Страницы: 32

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды