manualshive.com logo in svg

Deep Sea Electronics Plc DSE5110, Руководство по эксплуатации

Поделиться
Скачать
Deep Sea Electronics Plc DSE5110 Скачать руководство пользователя страница 43

 

DSE Model 5110 Automatic Start Engine Management Instrumentation System 

                 Part No. 057-009          5110 Operating Manual Issue 3.3        3/1/2006             

43

 

18 APPENDIX 

 

18.1  ALTERNATIVE WIRING TOPOLOGIES 

 

The 5110 series controllers can support different wiring topologies (AC systems) to suit the systems in 
use worldwide. The ‘Typical connection diagram’ details how to connect the module when used in a 3 
phase, 4 wire system (3 phase star connected alternators). Changes to this typical wiring diagram for 
other AC systems are detailed below.  

NOTE:-  The factory default configuration for the 5110 module is for use with the 3 phase, 4 

wire AC system. If another system is to be used, the controller must be reconfigured using the 
front panel editor detailed elsewhere within this manual. 

 

18.1.1  1 PHASE, 2 WIRE 

Single phase alternator with neutral conductor. 

 

18.1.2  3 PHASE, 3 WIRE 

Three phase alternator DELTA. 

 

CALL US TODAY 

1-888-POWER-58

REQUEST A QUOTE 

[email protected]

SHOP ONLINE 

www.genpowerusa.com

Содержание DSE5110























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды