Dedrone RF-300 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 20

Dedrone RF-300 Скачать руководство пользователя страница 6

The RF-300

Dedrone

6

v12.0 IM-Inst-RF300en

Parts of the RF-300

A

Antenna cover

E

Power button

B

Knurled nut

F

Network socket

C

RF Mounting Plate

G

Wi-Fi-antenna

D

Knurled head screw with sealing washer

2 The RF-300

The RF-300 is a passive, network-attached sensor for the detection and direction finding of radio
frequencies (RF) and Wi-Fi signals. In combination with two or more RF-300 it is able to determine
the position of a drone by the RF signals. The RF sensor detects targeted radio signals, identifies
their direction and sends the data, along with an alert to the DroneTracker System.

E

D

C

B

A

G

F

It scans a wide frequency band for radio frequencies and classifies them. The data is recorded and
available on the user interface DroneTracker UI.

3 Unpacking

This equipment should be unpacked and handled with care. Check the exterior of the packaging for
visible damage. If an item appears to have been damaged in shipment, notify the shipper immedia-
tely.

«
...
4
5
6
7
8
...
»

Содержание RF-300





















Отзывы:

Нет отзывов