background image

H A R D W A R E   O P E R A T I O N  

Data Device Corporation 

 

BU-65570/2i Manual 

23 

RT MODE 

The BU-65572iX can simultaneously simulate the operation of 31 unique 
remote terminals (RTs) plus a broadcast address for each of the 
installed channels. The BU-65572iX maintains "last status" and "last 
command" words allowing for full support of transmit last command and 
transmit status mode commands. The BU-65572iX supports full RT 
command illegalization for each transmit or receive message based on 
RT address and sub-address. In addition, individual mode commands 
may be illegalized. 

RT Error Injection 

Error conditions may be injected on an individual RT/SA basis. The  
BU-65572iX supports five categories of injected RT errors: length errors, 
encoding errors, gap errors, status address errors, and response errors. 
Length errors include both word count errors and bit count errors. Word 
counts of -32 to +1 words may be programmed. Bit counts of +3, +2, +1, 
-3, -2, or -1 bit may be programmed on any word within the message. 
 
Error specifications are attached to the data tables that are mapped to a 
RT and Sub-address combination. This provides for a large number of 
possibilities for injecting errors. An application can map more than one 
data table to any given RT/SA combination. This means that the RT can 
respond with different errors each time it is accessed.  
 
Encoding errors are implemented though the use of two simple yet 
powerful mechanisms for modifying the output of the BU-65572i'
Manchester encoder. The two modifying functions are glitch and inverse. 
A glitch will force the output of the encoder to an idle bus condition for 
the specified period of time. An inverse will invert the output of the 
encoder for the specified period of time. The word number, starting time, 
and width specify the placement of this error. The error may be placed in 
any word within the message. The starting time is programmed in 500 
nsec increments from the beginning of the specified word. The width of 
the error is specified in 50 nsec increments up to 3 

µ

sec. This error 

injection scheme lends itself to generating a host of errors including 
invalid sync patterns, parity errors, and Manchester bi-phase errors. 
 
A gap of 3, 4, or 5 

µ

sec (measured mid parity crossing to mid-sync 

crossing) may be inserted between any two words in message. This 
allows for a "dead time" gap between words of 1, 2, or 3 

µ

sec. A status 

address error may be injected in which the RT responds with a status 
word containing a RT address, which does not match the terminal's RT 
address. The RT may be programmed to respond with any value from 
zero to 31 in its status response. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание BU-65572iX











































Отзывы: