DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 16

DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 9

Assembling the Radiation Shield to Attach to the Top of a Post

Page 9

A

SSEMBLING

THE

R

ADIATION

S

HIELD

TO

A

TTACH

TO

THE

T

OP

OF

A

P

OST

The instructions for assembling the Radiation Shield differ slightly if you plan
to mount the Radiation Shield on top of a wooden post. Follow the instructions
below if (and only if) you plan to ultimately mount the Radiation Shield on top
of a wooden post.

Attaching Mounting Bracket

To attach the mounting bracket you will need a closed plate, the mounting
bracket, three 1/2” spacers, three #8 x 2 3/4” pan head screws, six #8 flat wash-
ers, three #8 split lock washers, and three #8 hex nuts. You will also need a drill
with a 3/16” (4.7 mm) drill bit.

Note:

You will need to supply three #8 x 1” screws if you plan to mount the Radiation Shield over the top of
the post (not preferred), instead of suspending it over the side edge.

M

OUNTING

ON

T

OP

OF

A

P

OST

1. Using the power drill with 3/16” (4.7 mm) drill bit, drill three holes through one of the

closed plates in the locations marked by the small dimples on the bottom of the plate.

Do not use the closed plate to which you attached the sensor.

D

RILLING

H

OLES

IN

C

LOSED

P

LATE

3/16" (4.7 mm) Drill Bit

Closed

Plate

«
...
7
8
9
10
11
...
»

Содержание 7714 Radiation Shield

















Отзывы:

Нет отзывов