DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 16

DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 12

Page 12

Radiation Shield Manual

M

OUNTING

THE

R

ADIATION

S

HIELD

Follow the instructions below to mount the Radiation Shield. There are sepa-
rate sections for each of the basic mounting options. You should modify the
instructions as necessary to fit your needs.

Mounting On the Side of a Post or Wall

In order to mount the Radiation Shield onto the side of a post or wall, you will
need the Radiation Shield assembly, three #8 split lock washers, three #8 flat
washers, and three #8 hex nuts. You will also need to supply four 1/4” x 1 1/2”
lag screws.

1. Using four 1/4” x 1 1/2” lag screws (not included), attach the mounting bracket to the

mounting surface in the desired location.

A

TTACHING

M

OUNTING

B

RACKET

TO

THE

S

IDE

OF

A

P

OST

2. Slide the stud ends protruding from the top of the Radiation Shield assembly into the

holes on the mounting bracket.

3. Secure the mounting bracket to the Radiation Shield using a #8 flat washer, #8 split

lock washer and #8 hex nut one each of the stud ends.

Tighten until the mounting bracket is firmly attached to the Radiation Shield

A

TTACHING

R

ADIATION

S

HIELD

TO

M

OUNTING

B

RACKET

#8 Lock Washer

#8 Hex Nut

#8 Flat Washer

Complete Plate

Assembly

«
...
10
11
12
13
14
...
»

Содержание 7714 Radiation Shield

















Отзывы:

Нет отзывов