manualshive.com logo in svg

DAVIS 7714 Radiation Shield, Руководство по установке, Страница: 6 / 16

Поделиться
Скачать
DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 6

 

Page 6

Radiation Shield Manual

 

Attaching the Support Plate to the Cover Plate

 

To attach the support plate, you will need the cover plate, the support plate, 
three #8 x 2 3/4” pan head screws, three 1” spacers, three #8 flat washers, three 
#8 split lock washers, and three #8 hex nuts.

 

1. Slide the three #8 x 2 3/4” pan head screws up through the non-threaded holes in the 

shield support plate.

 

Make sure the side of the support plate marked “UP” is in fact on top as you 
slide the screws in from the bottom.

 

2. Place the cover plate over the screw ends protruding from the support plate.

3. Place a 1” spacer over each of the screw ends.

4. Secure the support plate and spacers to the cover plate using a #8 flat washer, #8 

split lock washer, and #8 hex nut on each of the screw ends.

 

Tighten until the support plate is firmly attached to the cover plate.

 

C

 

OVER

 

 P

 

LATE

 

 A

 

SSEMBLY

Cover Plate

Cover Plate Assembly

Support Plate

#8 Hex Nut

#8 Lock Washer

#8 Flat Washer

1" Spacer

#8 x 2-3/4"
Pan Head Bolt

Содержание 7714 Radiation Shield

















Отзывы:

Нет отзывов