DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 16

DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 4

Page 4

Radiation Shield Manual

2. Position the second clip mount over the first, with the notch facing in the opposite

direction, securing the sensor cable between the two notches.

When positioning the second clip mount, make sure the raised semi-circle
faces down.

P

LACING

C

ABLE

I

NTO

C

LIP

M

OUNTS

3. Position the clip mounts over two of the mounting posts on the closed plate.

Make sure you orient the clip mounts as show in the figure below.

4. Attach the clip mounts to the mounting posts using two of the #4 x 1/2” pan head

self-threading screws and two of the #4 flat washers.

A

TTACHING

C

LIP

M

OUNTS

TO

R

ADIATION

S

HIELD

5. Once secured, adjust the position of the sensor so the sensor and approximately 1/4”

(6 mm) of cable protrude from the clip mounts.

6. Place the cable clamp around the sensor cable approximately 8” (20 cm) from the

sensor.

7. Secure the cable clamp to one of the remaining mounting posts (using a #4 x 1/2” pan

head self-threading screw and a #4 flat washer) so that a loop of cable is formed.

Make sure to mount the clamp with the flat side up and the bulge side
down. Tighten the screw completely so that the cable cannot move within
the cable clamp. If using the Stainless Steel Temperature Probe, wrap a cable
tie around the sensor and cable as shown below to hold the probe in place.

S

ECURING

C

ABLE

WITH

C

ABLE

C

LAMP

Clip Mounts

#4 x 1/2" Screw
#4 Flat Washer

Cable Clamp

External Temperature Sensor

Cable Clamp

Stainless Steel Temperature Probe

Cable Tie

«
...
2
3
4
5
6
...
»

Содержание 7714 Radiation Shield

















Отзывы:

Нет отзывов