DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 16

DAVIS 7714 Radiation Shield Скачать руководство пользователя страница 7

Attaching the Sensor

Page 7

Assembling the Plates and Studs

To assemble the plates and studs you will need the cover plate assembly as
well as the flat plate and closed plate with sensor, three #8 x 5” threaded studs
with attached #8 push nuts, three #8 flat washers, three #8 split lock washers,
and three plastic retainers.

1. Slide each of the three #8 x 5” (127 mm) threaded studs, with push nuts installed,

through each of the three holes in the closed plate, flat plate, support plate and cover
plate.

When inserting the threaded studs make sure that the short end (when mea-
sured from the push nut) goes through the plates. Screw the short end of the
threaded stud in until the cupped side of the push nut bottoms inside the
recess of the closed sensor plate. Tighten as much as you can by hand.

P

LATES

AND

S

TUDS

A

SSEMBLY

2. Place the Plates and Studs Assembly aside and proceed to the appropriate instruc-

tions for your installation.

If you are attaching the shield to the

side

of a post, to a pipe or to the Davis

Sensor Mounting Arm, continue with the instructions on page 8.

If you are attaching the shield to the

top

of a post, continue with the instruc-

tions on page 9.

Support Plate

Cover Plate

Assembly

Plates and Studs

Assembly

Flat Plate

Closed Plate

with Temp/Hum

Sensor

Threaded Studs

with push nuts

«
...
5
6
7
8
9
...
»

Содержание 7714 Radiation Shield

















Отзывы:

Нет отзывов