background image

27

Simple Maintenance and Service Activities

Miscellaneous

Every 500 km of cumulated running distance you should check whether all the screws are still firmly set. Tighten
them back as needed.

Care should be taken to remove sweat from the dashboard and the frame after every training session to protect
the paint against rust. Rust damage caused by sweat is not covered by the warranty!
Use a soft cloth wetted with water to clean the outer surface of the device. A light soap solution may also be used
to wet the cloth.

Replacing the V-belt

Required tools:

Phillips screwdriver

6mm Allen wrench

1

1

1

M 12 hexadecimal head bolt or recessed head bolt (commercially available)

and an appropriate wrench or Allen wrench

Procedure to replace the V-belt

Remove the protective cap (1) of the axle centre.

1.

Loosen the screw attaching the pedal rod (2).
(6mm Allen wrench).

2.

Screw in an appropriate M 12 bolt, with a hexadecimal
or recessed head, into the thread of the pedal axle until
the pedal comes off the axle shaft. Hold the pedal firmly
and remove it.

3.

Loosen the screws (3 to 5) on the lower right side cover.

4.

M 12

1

2

3

4

5

R

ight

side

The V-belt is located on the right side of the device.

Unplug the power cable from the main power supply before opening the device!

Take particular care to avoid damaging the internal parts of your ergo_bike while you
are working.

The manufacturer will not be liable for any damages arising as a result of negligence

while changing the V-belt!
V-belts are wearable parts and as such are not covered by the warranty.

Carefully remove the side cover.

5.

6.

The driving parts on the carrier plate /drive unit are now freely

accessible. Press on the belt tension lever and the tension

spring (9h) to release the V-belt tension, and then pull the belt

from the pulley (9a).

Follow the same steps (1 to 6) as described above in
reverse sequence to install the new V-belt.

Before installing the new V-belt, you should clean the belt slipping surfaces of the pulley and the drive shaft,
as well as the belt itself, with alcohol or cleaning petrol to remove the grease.

9a

9r

9p

tension

spring

9h

9c

Содержание Cardio pro



































Отзывы: