Datex DTX-200 Скачать руководство пользователя страница 11

Страница: 11 / 15

User's Manual DTX-200

Website: www.datex-dsm.com

_______________PARC D'ACTIVITES DE VILLEJUST - 9, place Marcel Rebuffat - 91971 COURTABOEUF CEDEX / FRANCE____________

S.A.S. au capital de 160. 000 € - R.C. EVRY B 331 142 018 - SIRET 331 142 018 00026 - APE 725Z- Int. VAT n° FR 81 331 142 018

Edition: May 2013

A single DTX

The default floppy drive emulator configurations will be set as shown in the picture

below. You will be able to see this configuration or change it as you remove the protective
cover found on the upper part the emulator.

Illustration 10: Drive select & terminators

ST25

DS2

DS1

ST17

ST15

Illustration 9: Jumper configurations

WARNING:

Both disk change jumper cannot be set at the same time.

The emulator above is in the basic configuration when delivered by DATEX:

The « drive select » jumper is at address 1.

It is equipped with terminators.

If your machine just uses one DTX, this one must be in this configuration.
Nevertheless, if your controller uses more than one drives (drive chain), you have to
take some precautions.

SING DRIVES CHAINS

Address 0

Drive select 0

Address 1

Drive select 1

Ready

Pin34

Disk

Connector

Ready

Pin34

Disk change

Pin 2

Disk change

Pin 34

Address 0

Drive select 0

Содержание DTX-200
















Результаты поиска

Содержание DTX-200

Отзывы:

Похожие инструкции для DTX-200

Бренды по названию

Популярные бренды

Datex DTX-200, Руководство пользователя

Результаты поиска

Содержание DTX-200

Отзывы:

Похожие инструкции для DTX-200

Бренды по названию

Популярные бренды