Datex DTX-200 Скачать руководство пользователя страница 14

Страница: 14 / 15

User's Manual DTX-200

Website: www.datex-dsm.com

_______________PARC D'ACTIVITES DE VILLEJUST - 9, place Marcel Rebuffat - 91971 COURTABOEUF CEDEX / FRANCE____________

S.A.S. au capital de 160. 000 € - R.C. EVRY B 331 142 018 - SIRET 331 142 018 00026 - APE 725Z- Int. VAT n° FR 81 331 142 018

Edition: May 2013

Terminators :

Only a disk (or emulator) must be equipped with terminators in a daisy chain.

You must remove it from the disks and leave it just on one disk.

Remove the terminators :

You just have to pull up the terminators to remove it from the card:

WARNING:

When you remove a component from the card, you must take care to pull it

straight up to avoid breaking pins.

- When you remove terminators, take care of their direction.

If you want to replace them on the card, they will have to be on the direction they were
when you removed them.

The pin 1 is towards the end of the termination, opposite of the supply.

Illustration 13: Remove a terminator

Terminator

Pin 1

Содержание DTX-200
















Результаты поиска

Содержание DTX-200

Отзывы:

Похожие инструкции для DTX-200

Бренды по названию

Популярные бренды

Datex DTX-200, Руководство пользователя

Результаты поиска

Содержание DTX-200

Отзывы:

Похожие инструкции для DTX-200

Бренды по названию

Популярные бренды