manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Техническое описание слота

Поделиться
Скачать
Datex-Ohmeda S/5 M-NIBP Скачать руководство пользователя страница 39

NIBP Module, M-NIBP

Document No. 800 1015-1

35

Item

Item description

Order No.

10

Cross cylinder-head PT screw 3x10

628703

11

NIBP frame, M-NIBP

880427

13

Safety valve (overpressure valve)

 877109

14

NIBP pump, M-NIBP (Rev. 01-02)

*(880363) Use 883346

15

Plastic pump cover, M-NIBP

879176

16

Front panel sticker

see 6.1.5

17

LED board, M-NIBP (Rev. 01-03)

880361

18

Hose connector

64654

19

Cross cylinder-head screw M2.5x6

628700

20

Port plug for magnetic valve

58535

21

Magnetic valve

*58534

22

Pulse valve

*880365

6.1.2

 

NIBP Module, M-NIBP Rev. 02

Item

Item description

Order No.

8

NIBP board, M-NIBP (Rev. 02)

*(882418) Use 883011

1)

 883902

23

Check valve

58542

1)

 NOTE: The NIBP board 883011 can be used as a replacement only with NIBP software 883902.

6.1.3

 

NIBP Module, M-NIBP Rev. 03

Item

Item description

Order No.

-

NIBP software

*883902

8

NIBP board, M-NIBP (Rev. 03)

*883011

14

NIBP pump, M-NIBP (Rev. 03)

*883346

Содержание S/5 M-NIBP

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды