manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Техническое описание слота

Поделиться
Скачать
Datex-Ohmeda S/5 M-NIBP Скачать руководство пользователя страница 35

NIBP Module, M-NIBP

Document No. 800 1015-1

31

Watchdog BEEP

Connect manometer to the front panel and pump pressure into the module. When the AD5 value

changes from negative to positive value (at about 5 mmHg) a beep is heard. This is the watchdog

threshold pressure. Beyond this pressure the watchdog is active and cut pressures at about 2 min.

(adult).

5.1.7

 

NIBP Watchdog menu

NOTE: Parameter values in Service Data are for reference only.

Test ADULT

Test ADULT

 is to test watchdog timer in adult mode (120 to 140 seconds).

Test INFANT

Test INFANT

 is to test watchdog timer in infant mode (about 60 to 70 seconds).

Stop Test

Stop Test is for stopping the test.

Watchdog Data

See NIBP Service menu in chapter 5.1 for information on general items 

Pressure,

 

Zero, Protect

handle,

 

Calibr. prot., +15 V power, AD0 

to 

AD7 

as well as

 Timeouts etc.

Watchdog Interval 

shows the time the +15 Vdirty stays on during the test.

Adult watchdog time testing

Select Test ADULT and press the ComWheel. Watchdog interval starts counting up seconds and

keeps on counting as long as the +15 Vdirty is on. The time should be 120 to 140 seconds.

Infant watchdog time testing

Select Test INFANT and press the ComWheel. Watchdog interval starts counting up seconds and

keeps on counting as long as the +15 Vdirty is on. The time should be 60 to 70 seconds.

Содержание S/5 M-NIBP

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды