manualshive.com logo in svg

Datex-Ohmeda S/5 M-NIBP, Техническое описание слота

Поделиться
Скачать
Datex-Ohmeda S/5 M-NIBP Скачать руководство пользователя страница 10

Datex-Ohmeda S/5 monitors

Document No. 800 1015-1

6

Memory

NIBP program memory (EPROM) size is 128k 

×

 8. RAM size is 32k 

×

 8 bit and it stores variable

values in NIBP measurement. EEPROM is size 64 

×

 16 bit and is used to store the calibration

values for the pressure transducers, the pulse valve constants gained during measurements, the

PC board identification, and module serial number.

Software control

Software controls valves and pump. In addition to the individual on/off signals for each component

there is a common power switch for the valves and the pump that can be used at pump/valve

failures.
In addition to external RS485 reset line the microprocessor system is equipped with its own power-

up reset.

Watchdog timer

The NIBP board is equipped with software independent safety circuit to disconnect supply voltages

from the pump and the valves if the cuff has been pressurized longer than preset time. As soon as

the cuff pressure rises over a specified pressure limit, timer starts counting. The timer is adjusted to

stop the pump and open the valves in 2 minutes 10 seconds in adult/child mode and in 1 minute

5 seconds in infant mode.

Valves

Exhaust valves are used for emptying the cuff and the joining chamber after the measurement.

Exhaust valve 1 is also used as safety valve in infant mode. Valve opens at 165 mmHg. Exhaust

valve 2 is also used as safety valve in adult mode and opens at 320 mmHg.

Bleed valve is used for emptying the cuff during measurement. Zero valve is used for connecting

the pressure transducer B1 to open air.

Power supply section

All connections are established via 25-pin connector (D-type, female). The module needs +5 V,

±

15 V, and +15 VD (dirty) power supply to operate. The pump and the valves use se15 VD

power line. The supply voltages are generated in the power supply section of the S/5 monitor. The

reference voltages 

±

5 V

ref

 and +10 V

ref

 are generated on the NIBP board.

Содержание S/5 M-NIBP

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды