background image

PAGE 5

3.0 - ACCESSORIES POSITIONING

3.2

 

-

 

Contact

 

switch

 

(

Thatcham Requirement

)

If Thatcham accreditation is not a requirement the fitting of the switch is 

optional but strongly recommended.  If the switch is not fitted, the 

GREEN/BROWN wire should be insulated but  remain free for other 

possible uses such as programming the alarm or learning new devices.

NB:

A contact switch can be must be fitted to protect the alarm ECU. It must be 

installed in such a way as to detect the opening of the seat or panel without 

being accessible from the outside. The trigger threshold must be carefully 

set to avoid false alarms.

Do not ground the switch terminal to the vehicle frame make a connection to 

earth through a negative cable such as the indicator lamp negative lead.

Override

key

PAGE 4

Override key

Example of receptacle positioning on the vehicle

plastic side cover

4.0 - ALARM UNIT SEALING

Alarm unit sealed

To seal the alarm, position the

rubber cap over the external edge

of the alarm housing.

Pull the plastic rectangular flange

over the rubber cap and secure

with the supplied screws.

Do not over tighten.

3.1 - Override key receptacle

The receptacle with built-in LED must be installed where it can readily be seen

and accessed by the user. Before drilling a hole in the plastic dash with a 13mm

drill bit, check the position of the handlebars with the steering lock engaged.

Make sure the LED will not be covered by the handlebars when the vehicle is

parked.

Содержание EVO PRO










Отзывы: