Datacom Systems DS-1404 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 55

Datacom Systems DS-1404 Скачать руководство пользователя страница 13

Datacom Systems Inc. 2016

13

DURAstream

™

DS-1404, DS-1406, DS-2408 FASTstart Guide

2.6 Front - Power & Status Indicators

On the front panel, the power status of the device can be determined through three
indicators labeled “POWER 1”, “POWER 2”, and “STATUS”.

The LEDs located next to each power label will illuminate

green

when a power supply is

connected and switched ON.

When the power indicators illuminate

red

, it indicates that there is either not a power

supply connected, or it is not switched ON.

Although only one power source is required to power the DURAstream™, use of a second
independent power source is strongly recommended to assure maximum link uptime.

The “STATUS” LED indicator flashes

green

during the boot-up cycle and turns solid

green

upon a successful boot sequence indicating the DURAstream™ is operational.

2.7 Rear - Power Ports

Each DURAstream™ has two power ports on the back. These dual redundant power ports
should be connected to power supplies on two separate circuits to ensure maximum link
uptime. These LED indicators function in unison with the “POWER 1”, and “POWER 2”
indicators on the front of the device.

«
...
11
12
13
14
15
...
»

Содержание DS-1404
























































Отзывы:

Нет отзывов