manualshive.com logo in svg

Dantel 46062-02, Руководство по установке и эксплуатации

Поделиться
Скачать
Dantel 46062-02 Скачать руководство пользователя страница 11

46062-0299 <90-00016>

 P

AGE

 11

S

TRAP

 S

ETTINGS

Set the straps as required for the specific application.

There are no strap settings for the printer port; RS-232 is the
only interface available on this port.

The straps for the master and data ports are located beneath the
power supply subassembly; refer to Fig. 5 for the location of the
power supply. To access the straps:

♦

Remove the four screws securing the subassembly.

♦

Pull the subassembly straight up, exercising caution not to
bend the subassembly connector pins.

Refer to Figs. 10 and 11 for the specific strap locations for
RS-232 and RS-422 asynchronous communications on the
master and data ports.

NOTE:

Many straps in Fig. 11 are reserved for future use. For
additional information regarding strapping options, refer to
Tables A and B.

Asynchronous operation of the RS-232 interface requires only
three lines: the transmit and the receive lines and signal
ground. Handshaking lines are also available.

Asynchronous operation of the RS-422 interface requires four
lines: transmit positive and negative polarity lines and receive
positive and negative polarity lines.

The printer port always operates in asychronous RS-232 mode
and requires no straps. Contact Dantel’s Field Service depart-
ment for more information about the following applications:

♦

Asynchronous RS-232 operation requiring handshaking

♦

Synchronous RS-232 or RS-422 operation

♦

Applications not shown in Figs. 10 and 11.

Straps X1 and X2 allow electrical disconnection of the backup
battery for storage or shipment. Set strap X1 for normal opera-
tion. Set strap X2 for shipment or storage. The GPP ships with
strap X2 set. Reset the strap to X1 during installation.

NOTE:

The on-board GPP battery is designed to retain the database
configuration during momentary power outages only. It is not
intended for long-term storage of databases and is not
rechargeable. The battery will begin to discharge when two
conditions are met: (1) The X1 strap is in, and (2) power has
been removed from the module. When the GPP is not in use,
place this strap in the X2 position.

INSTALLATION

Содержание 46062-02

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды