Danley DNA 5k4c Скачать руководство пользователя страница 3

Страница: 3 / 31

Page 3 of 31

Table of Contents

Important Safety Information ................................................................................................... 2

Regulatory Compliance ...................................................................................................... 2

Thanks and Unpacking ............................................................................................................. 5

Introduction and Key Features .................................................................................................. 6

Front Panel ............................................................................................................................ 13

Power Switch ................................................................................................................. 13

Power ON indicator ......................................................................................................... 13

Bridged Mode indicator ................................................................................................... 13

Control Software Online indicator ..................................................................................... 13

Protect ........................................................................................................................... 14

User DSP indicator .......................................................................................................... 14

User DSP Setting Defeat button ....................................................................................... 14

Input Signal Indicators .................................................................................................... 14

Rear Panel ............................................................................................................................. 15

Power Inlet .................................................................................................................... 15

Audio Input Connectors ................................................................................................... 15

Audio Output Connectors ................................................................................................ 15

Communications Port Connections ................................................................................... 16

Mechanical Installation ............................................................................................................. 7

AC Power Connection ............................................................................................................... 9

Audio Connections ................................................................................................................. 10

Using unbalanced connections ......................................................................................... 11

Amplifier output connections ........................................................................................... 11

100V line operation ................................................................................................................ 12

PodWare Amplifier Control Panel ............................................................................................. 17

Amplifier Channels .......................................................................................................... 18

User Controls ................................................................................................................. 18

Monitoring Section (MonIcon) .......................................................................................... 18

User DSP ........................................................................................................................ 19

Main Control Panel .......................................................................................................... 20

Hidden Controls .............................................................................................................. 21

Saving & Recalling Data .................................................................................................. 21

Loading Factory Presets .................................................................................................. 22

Tool Bar ......................................................................................................................... 22

Keyboard Shortcuts ......................................................................................................... 22

Audio Processing ............................................................................................................ 23

Equalisation Filters .......................................................................................................... 24

Bridge Mode ................................................................................................................... 24

Protection ...................................................................................................................... 25

Limiters .......................................................................................................................... 25

Indication ..........................................................................

Error! Bookmark not defined.

Содержание DNA 5k4c
































Результаты поиска

Содержание DNA 5k4c

Отзывы:

Похожие инструкции для DNA 5k4c

Бренды по названию

Популярные бренды

Danley DNA 5k4c, Руководство пользователя

Результаты поиска

Содержание DNA 5k4c

Отзывы:

Похожие инструкции для DNA 5k4c

Бренды по названию

Популярные бренды