Danley DNA 10K4 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 49

Danley DNA 10K4 Скачать руководство пользователя страница 21

21

Ethernet Communications Port-‐

The device may be controlled entirely from another controller, typically a Personal

Computer, running an application that is compliant with the ObCom standard such as PodWare. Connection will
normally be made to the controller via this Ethernet port connector. This port is also used for updating the firmware in
the unit.

Auxiliary Port-‐

The auxiliary port may be configured to recall snapshots or apply muting.

Networked Audio Ports

-‐ The device has the option for networked audio ports; if none are required a blanking plate

will be fitted. There are several options for networked audio including Dante™. For a full list please consult your
vendor.

Power Inlet

-‐ The unit should be connected to a suitable mains electricity supply using an earthed Powercon connection

power lead. The device has a switch mode power supply that is capable of operating with a nominal mains voltage of
100V to 230V, 50/60Hz without re-‐configuration.

NOTE: The device must be earthed to a suitable power earth; failure to do so may affect performance and/or operation
and will invalidate warranty and could be potentially hazardous.

Audio Input Connectors-‐

All audio connections are fully balanced and wired: pin-‐1 to ground (as required by the AES48

standard), pin-‐2 hot & pin-‐3 cold.

Loudspeaker Connectors-‐

The amplifier Speakon

TM

outputs. Connect the loudspeaker to the 1+ and 1-‐ terminals. CH1

also carries the (duplicated) loudspeaker output for channel 2 on terminals 2+ and 2-‐. Similarly, CH3 carries the
loudspeaker output for channel 4 on terminals 2+ and 2-‐. For Bridged mode, use terminals 1+ and 2+ of either CH1 or
CH3.

Relay output-‐

This isolated relay output may be used to indicate abnormal conditions to external monitoring

apparatus. See

Fault Relay

AES3 Audio Input Connectors-‐

For inputting Digital Audio signals. The Input is fully balanced and wired: pin-‐1 to

ground, pin-‐2 data+ & pin-‐3 data. The Link connector allows a buffered AES3 signal to be passed on to another device.

«
...
19
20
21
22
23
...
»

Содержание DNA 10K4


















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды