Danley DNA 10K4 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 49

Danley DNA 10K4 Скачать руководство пользователя страница 18

18

Audio Connections

Input Connections

For each input channel there   is a   female   XLR input connector.   Even channel numbers are for
Analogue inputs only. Odd   channel numbers are either for Analogue inputs (when   in   Analogue input
mode) or for AES3 input pairs (when in AES3 input mode).
The HOT, +   or ‘in phase’ connection should be made to pin 2   of the XLR connector.
The COLD, -‐ or ‘out of phase’ connection   should   be made to   pin   3 of the XLR   connector.
Pin 1   of the   XLR connectors is internally connected to the   chassis. The   shield of the input cable
should always   be connected Pin 1   of the   XLR to ensure that   EMC performance and regulations are
met.

2

1

3

Pin 2 HOT +

Pin 3 COLD -

Pin 1 Shield

Input XLR balanced connection

Using unbalanced connections

Please   note   that the   use   of unbalanced connections is not recommended, however when   connecting
the amplifier to an unbalanced audio source, the   signal conductor should be   connected to XLR pin2.
The ‘Cold’ conductor or cable screen should be connected to XLR pin 1   with a   short connection made
between   pin   1 and   pin   3.

2

1

3

HOT +

Shield

Input XLR unbalanced connection

Amplifier Output Connections

The amplifier is fitted with one Speakon

TM

connector per amplifier channel. The appropriate

conductor terminations are shown below and on the rear panel of the unit.

«
...
16
17
18
19
20
...
»

Содержание DNA 10K4


















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды